We wanted it to be super solid so, with the wall unfolded and upright, I drilled two 1/2″ holes through both center frame pieces with the 1/2″ wood spade bit. The Barrel Bolts hold the wall quite well but there was a little give if you pressed on the top of the wall. I then folded the wall again and, with my daughter holding the wall upright, drilled a pilot hole in the center of each mark and then drilled through the 2 x 4 frame with the 1/2″ wood spade bit. In order to know where to drill the Barrel Bolt holes, I folded the wall in half, used a pencil to color the bottom of the Barrel Bolt, opened the wall back up and pushed the Barrel Bolt onto the bottom frame to mark where the hole should go. Note: The front plywood pieces were not attached at this point but I failed to take pictures. Be sure to measure for your exact dimensions.)Īt this point, we attached the hinges in four places and used the 1/2 wood spade to drill holes for the Barrel Bolts to go through. (I cut mine at 25″ because the numbers added up that way but the top ended up slightly wider than the bottom. The side horizontal braces sit just above the barrel locks and are 24-7/8″. The center cross 2 x 4 brace is 28″ and sits inside the vertical 2 x 4’s. The 2 vertical 2 x 4 braces should be cut at 34-1/2″ or 1-1/2″ less than 3′. This gives you a good idea of how the frame pieces were attached. I did not have the plywood attached at this point but failed to take pictures. Note: The picture above shows the wall with the plywood attached. We used wood glue, our Kreg Corner Clamp, and 2-1/2″ Kreg Screws to attach our bottom frame pieces.īefore we attached our top frame pieces, we attached our Barrel Bolts to the inside bottom of each side frame 2 x 4. Tip: Wait until you build the frame and then measure to make sure you get the right measurement for the inside pieces. The 2 x 4 center pieces for the 4′ base were cut at 45″ or 3″ less than 4′ (because the top and bottom 2 x 4’s account for the 3″ difference. Then, we cut 3 top and bottom pieces at 81″ or 3″ less than 7′. We cut each side piece for the top at 3′ and each side piece for the bottom at 4′. The entire wall would have dimensions of 7′ x 7′. Photo Backdrop Wallįor the wall, we knew we wanted the lower portion to be 4′ tall and the top portion to be 3′ tall. We finished the triangle legs with a quick sand and they were ready to paint. Once everything was attached, we used Kreg Pocket Hole Plugs and plastic wood to fill our pocket holes in the legs, since they would be visible. We used 2-1/2″ Kreg Screws and wood glue to attach the 2 x 4 to the bottom of the triangle legs. Here, you can see the 4 pocket holes we drilled to attach a 2 x 4 to the bottom of our triangle legs. We drilled 4 pocket holes in the bottom of each triangle leg to make this happen. Our triangle legs needed to be attached to a 2 x 4 base in order to have a ledge for our wall to sit on and to have a place to attach our casters. You can see the backside of the 1/2″ holes on the picture below. Then, we used a 1/2″ wood spade bit to drill the rest of the way through the 2 x 4’s for our carriage bolts to fit through. This would allow the top of our carriage bolts to sit recessed inside. Next, we used a 1-1/8″ wood spade bit to drill a half inch depth in both the top and bottom using the pilot hole. However, we knew the hole in the bottom piece had to allow for room for a 2 x 4 base (on the wall) so that hole was toward the top of the base. One in the top tip of the triangle and the other in the middle of the bottom board. Once our triangle legs were put together, we drilled pilot holes where we wanted to attach the triangle leg to the 7 x 7 wall. This allowed us to attach our triangle pieces together with 2-1/2″ Kreg Screws. Then, we drilled two pocket holes with our Kreg Jig on one end of each board and sanded each piece. We cut 6 – 2 x 4’s at a 30º angle on both ends at 23-3/4″ at the longest side. We found many variations online and settled with our own version of the triangle leg! The first thing we had to wrap our minds around was how to make a 7 x 7 wall stand upright. How To Build A Folding Backdrop Wall On Wheels Photo Backdrop Triangle Legs White Exterior Paint (I used 1/2 of 1 gallon).When you purchase through an affiliate link, we receive a small commission at no additional cost to you. It was up to me and Justine, my daughter, to come up with our own plans! DIY Photo Backdrop Wall I searched the internet but couldn’t find a Wall On Wheels that could Fold. It took me a while to wrap my head around this project. That meant the wall had to fold so height wouldn’t be an issue on the road. A Wall On Wheels that could easily be loaded on a truck and used at shows. My niece had vision for a transportable, Photo Backdrop Wall.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |